Control Enclosure

2026-11-03

The Equipment to be purchased under the Contract is generally described as follows : One ( 1 ) fully equipped pre fabricated metal Control Enclosure , including all power panelboards ( AC and DC ), Relay Panels , SCADA / Communications Panels , Battery Systems , and misc . supporting materials and equipment . Technical Specifications are included as a part of this Contract . Items referred to as “ Division 1 ” or “ Div 1 ” documents within the Technical Specifications shall be defined as Sections 100 - 1000 of this Contract . Bid Item Specification Section Description Unit Unit Price Qty Extended Price Proposed Manufacturer Delivery - Weeks After N - T - P * 401 1000 One ( 1 ) fully equipped pre fabricated metal Control Enclosure , including all power panelboards ( AC and DC ), Relay Panels , SCADA / Communications Panels , Battery Systems , and misc . supporting materials and equipment . Technical Specifications are included as a part of this Contract F . O . B . Monthill Substation 4095 E . Flamingo , Las Vegas , NV 89121 . Each 1 EQUIPMENT 1 . Quality Assurance . 1 . 1 Conform to applicable specifications , codes , standards , and requirements of regulatory agencies . 1 . 2 Provide equipment or material that comply with the requirements of the Contract Documents , undamaged , and , unless otherwise indicated , new and unused at the time of installation . Provide equipment or material that are complete with all accessories , trim , finish , safety guards , and other devices and details needed for a complete installation and for the intended use and effect . 1 . 2 . 1 Where they are available and if they comply with the Contract Documents , provide Equipment of types that have been produced and used successfully in similar situations on other projects . 1 . 2 . 2 Where , because of the nature of its application , CRCNV is likely to need replacement parts or additional amounts of the Equipment at a later date , either for maintenance and repair or replacement , provide standard products for which the manufacturer has published assurances that the Equipment and its parts are likely to be available to the CRCNV at a later date . 1 . 3 Comply with size , make , type , and quality specified , or as specifically approved in writing by the CRCNV . 1 . 4 If the Equipment is manufactured or fabricated : 1 . 4 . 1 Design , fabricate and assemble in accordance with the best engineering and shop practices . 1 . 4 . 2 Manufacture like parts of duplicate units to standard sizes and gauges , to be interchangeable . 1 . 4 . 3 Two or more items of the same kind and by the same manufacturer must be identical . 1 . 4 . 4 Equipment must be suitable for the service conditions intended . 1 . 4 . 5 Capacities , sizes and dimensions shown or specified must be adhered to unless variations are specifically approved in writing . 2 . Transportation and Handling . 2 . 1 The Contractor shall prepare Equipment for shipment in a manner to facilitate unloading and handling , and to protect against damage or unnecessary exposure in transit and storage . Provisions for protection must include the following : 2 . 1 . 1 Crates or other suitable packaging materials . 2 . 1 . 2 Covers and other means to prevent corrosion , moisture damage , mechanical injury , and accumulation of dirt in motors , electrical equipment , and machinery . 2 . 1 . 3 Suitable rust - preventative compound on exposed machined surfaces and unpainted iron and steel . 2 . 1 . 4 Grease packing or oil lubrication in all bearings and similar items . 2 . 1 . 5 Moisture absorbing media in cabinets and electrical enclosures . 2 . 2 Tag or mark each item of Equipment with the Contract Number and Bid Item number as identified in the Contract Documents or on Compliance Submittals . Include complete packing lists and bills of material with each shipment . Each piece of every item need not be marked separately provided that all pieces of each item are packed or bundled together and the packages or bundles are properly tagged or marked . 2 . 3 The Contractor shall mail bills of material to the CRCNV prior to delivery of each shipment and shall include bills of material with each shipment . 2 . 4 Furnish the CRCNV with all requirements for unloading and handling of Equipment upon delivery sufficiently in advance to allow the CRCNV sufficient preparation time . Include type and capacity of unloading equipment required as applicable . 2 . 5 Deliver all Equipment by truck . 2 . 6 Deliver Equipment in an undamaged condition , in original containers or packaging , with identifying labels intact and legible . 2 . 7 Mark partial deliveries of component parts to identify the Equipment , to permit easy accumulation of parts , and to facilitate assembly . 2 . 8 The CRCNV shall receive , check , unload , inventory , accept and store all Equipment delivered to the specified location in accordance with proper notice .

Nevada

2026-05-01