HMA Skip Paving - M - 15 in Oakland County

2026-11-03

This is a Request for Proposal ( RFP ) for services to perform HMA milling and paving along M - 15 between South of Granger Rd to County Line Rd . Work under this contract will require milling , removal and disposal of existing bituminous asphalt , installation of binder , installation of finished course of hot mix asphalt , providing traffic control , installing shoulder line Corrugations , pavement markings , and other defined work . REQUIREMENTS General Requirements Contract Activities must be performed on three ( 3 ) consecutive weekends ( Saturday and Sunday ). The Contractor shall provide all labor , material , equipment , supervision , and any incidental services or items required to perform Contract Activities . Except where otherwise indicated within this Schedule A , all materials and workmanship shall be in accordance with the MDOT Standard Specifications for Construction , 2020 Edition [ see MDOT 2020 Standard Specifications for Construction [ WEB ]- linked ( michigan . gov )], and in accordance with any relevant / applicable Frequently Used Special Provisions ( 2020 ), and any relevant / applicable Supplemental Specifications ( 2020 ). At no point shall work begin without a representative from MDOT on site . The Contractor must not leave equipment and / or store equipment overnight on any trunkline , State right - of - way , or public recreational property during the performance of the Contract . The Contractor must not operate or park equipment or store materials within a tree drip line . All local noise , dust , and work - hour ordinances shall apply to the Contract . MDOT will not be responsible for any cost associated with the disposal of any service provided in the Contract . MDOT will not be responsible for any citations , fines or tickets received , while performing Contract Activities . The Contractor shall take any other actions themselves or as directed by MDOT , to protect the safety and health of the public , state employees , State property and property of the local unit of government during the performance of the Contract . The Contractor shall conduct and supervise work as to ensure its completion in accordance with the terms of this contract and the approved progress schedule . MDOT Program Manager reserves the right to shut down any construction operations if no proper communicable notice is received from the Contractor . Specific Requirements The approximate paving limits within the project area may be viewed in the Google Earth map at https :// earth . google . com / earth / d / 1QyWxHBNmpnPDiYPGpFHMNMwDuoweHJEC ? usp = sharing . Paving repair locations are estimated and provided for reference only . Actual work performed will be determined by the MDOT Program Manager . Final locations will be marked by the MDOT Program Manager or representative before the start of the project and are subject to change at the time of marking . DESCRIPTION OF SERVICES Work includes continuous cold milling and paving of two inches ( 2 ”) of the existing pavement , replacing pavement markings , shoulder line corrugations and milling and surfacing of approaches at the discretion of MDOT . Cold Milling and Hot Mix Asphalt All milling and paving work must be performed per Section 501 . Plant - Produced Hot Mix Asphalt of the MDOT 2020 Standard Specifications for Construction . All paving locations and limits will be determined and marked by MDOT prior to the start of milling operations . HMA surface removal depth and limits will be at the discretion of MDOT . Contractor may be required to cold mill and patch more than two inches ( 2 ”) to achieve the required cross - section and adequate base condition . Contractor must ensure the final pavement cross slope conforms to MDOT Standard Requirements of 2 . 0 % along the main traveled way and 4 . 0 % along the shoulder , unless otherwise approved in writing by the MDOT Program Manager . A uniform 2 . 0 % cross slope on the shoulder for ease of paving operations will not be permitted , as it may create a drop - off at the shoulder edge and require additional shoulder aggregate and / or restoration resulting from nonconforming pavement slopes . Any such non - compliance work shall be rejected and the corrective work shall be performed by the Contractor without any additional cost to MDOT . Traffic loops and traffic counters must be protected from damage during the cold milling operation . Any damage caused by the Contractor ’ s operations is not permitted unless explicitly approved in advance by the MDOT Program Manager . All milled areas shall be filled during the same closure in which they are milled , and no milled area shall remain unfilled longer than 12 hours from the time milling occurs . The mix for skip paving will be MDOT approved design 5EML with PG 70 - 28P binder . A minimum in - place compaction of at least 92 % will be required with third party density testing to be conducted at the discretion of the MDOT . Shoulder Line Corrugation , Milled , HMA Contractor must inventory all existing shoulder line corrugations prior to cold - milling the pavement . Contractor must re - install center line corrugations on the newly paved HMA surface per inventory and in accordance with MDOT Standard Plan for Shoulder and Center Line Corrugations , R - 112 - J ( see R - 112 - J ). The approximate start and stop locations of the shoulder corrugations within the project limit may be viewed in the Google Earth map at https :// earth . google . com / earth / d / 1WXL8X6J5PLn6W8_X21aqsmJqgSexMOqf ? usp = sharing . Final locations will be marked by the MDOT Program Manager or representative after the completion of final paving operations . This service item includes all labor , material , and equipment necessary to complete the work as described , including containment , collection , and disposal of spoils . No additional payment will be made for beadless waterborne layout lines . All other pavement marking payments will be paid for under the appropriate pavement marking pay items .

MITN

2026-04-29